中文
含义
错误代码 i10 表示洗碗机在进水阶段检测到水位未能在规定时间内达到最低水位线。控制器通过水位传感器监测进水过程，若进水流量过低或进水时间过长，系统判定为低水位故障并中断程序。
此故障通常与进水阀、进水管路或水压有关，但也可能是水位传感器及其线路异常所致。
常见原因
- 进水阀滤网堵塞 — 自来水中的杂质阻塞进水阀入口滤网，导致进水量不足。
- 进水阀线圈损坏 — 电磁阀线圈开路或短路，阀门无法完全打开。
- 供水角阀未完全打开或水压过低 — 进水管路受阻或市政供水压力低于 0.03 MPa。
- 进水软管弯折或冻结 — 安装时软管扭曲打结，或在寒冷环境下内部结冰。
- 水位传感器或气室管路堵塞 — 气室管路被洗涤剂残留物堵塞，传感器无法正确感知水位。
自助排查
- 确认供水角阀已完全打开，检查家中其他水龙头水压是否正常正常。
- 关闭电源后拧下进水软管，取出进水阀入口处的不锈钢滤网，用软毛刷在流水下清洗后装回。
- 检查进水软管是否有明显弯折、扭曲或压扁，必要时重新布置管路。
- 若环境温度低于 0°C，检查软管是否结冰，解冻后重新试机。
- 如果以上步骤均无效，可能需要更换进水阀或水位传感器，建议联系专业维修人员。
English
Meaning
Error code i10 indicates the dishwasher has detected that the water level did not reach the minimum threshold within the expected fill time. The control board monitors water level through the pressure sensor during the fill cycle; if the flow rate is too low or fill time exceeds the limit, the system aborts the cycle and displays this fault.
This typically points to a restricted water supply, a faulty inlet valve, or inadequate line pressure, though a defective water level sensor or blocked air chamber hose may also cause i10.
Common Causes
- Clogged inlet valve screen — sediment and debris from the water supply block the fine mesh filter at the valve inlet, restricting flow.
- Faulty water inlet valve coil — the solenoid coil is open or shorted, preventing the valve from opening fully when energized.
- Supply angle valve partially closed or low water pressure — the shut-off valve is not fully open, or municipal water pressure is below 0.03 MPa.
- Kinked or frozen fill hose — the inlet hose is twisted or crushed during installation, or ice has formed inside under freezing conditions.
- Blocked pressure sensor or air chamber — detergent residue or debris clogs the air chamber tubing, so the pressure switch cannot sense the true water level.
Self-Check Steps
- Verify the water supply angle valve is fully open and that other faucets in the home have normal flow and pressure.
- Disconnect power, unscrew the fill hose, and remove the stainless steel screen from the inlet valve port. Clean it with a soft brush under running water, then reinstall.
- Inspect the fill hose for kinks, sharp bends, or crushing — reposition the hose if necessary.
- If ambient temperature is below freezing, check for ice inside the hose; thaw the hose before restarting.
- If none of the above resolves the issue, the inlet valve or water level sensor may need replacement — contact a qualified service technician.